Skip to main content

The Build 1


Okay here is how to build the two ships I said I would show you how to build.

This is for the fighter:

First collect the pieces below.  


2nd: Attach the arch to the black brick with side studs. 


3rd: Apply the gray pieces with two holes each on the sides. 


4th: Add on the orange highlight piece to the black arch.


5th: To make the missiles, attach the blue cones to the gray technic pieces and for the other two
missiles, attach the the two red studs to the two green studs and then attach them to the gray technic pieces. 


6th: Put the missiles in the gray holed pieces as shown.


Final step: Add the orange cone to the end of the arch and then your done!


Here is how to build the long red distracter ship:

1st: get these pieces from your collection.


2nd: Add the little yellow pieces to the bottom of the red piece.


3rd: Put the red piece to the side for now and get the black piece with side studs and add on the two hinged bricks to he side.


4th: Add on the grill plates to the top of the hinged bricks.


5th: Add on the wings.


6th: Attach the piece above to the long red piece.


7th: Attach the jumper plate.


8th: Add on the blue slope to the jumper plate.


And there you have it! How to make the two spaceships.


Hope you enjoyed this!


Comments

Post a Comment

Popular posts from this blog

War Machine-HULKBUSTER!

Hello and welcome to another epic post from Legomaster. This week I will be showing you a longterm project that I have been working on for over 2 months. I did not build every day, some weeks I did nothing at all, sometimes only one or two small adjustments.  Here I present it to you: The WAR MACHINE HULKBUSTER!!! It's a little over 9 inches tall and 6 inches wide. Now for the functions. Here is the cockpit inside the chest that opens on a small hinge. Here is a arm, which has 3 fingers, a gun, and a quad-piston extenders. Here is a cool fact: The upper part of the arm is a 6 stud shooter and the shoulder protectors are nexo knight shields.  Up here you can see the main gun which has 4 rotating barrels(in my imagination) to mow down enemies. The hulkbuster is powered by not 1, not 2, but 3 arch reactors! How else will you power all those mechanics? The round brick on top is to hold the War Machine helmet once I get a War Machine minifigure.
4 comments
Read more

Pacific Rim Jaegers, Fan Design!

Hello and welcome to anther post from Legomatic. I know I just posted yesterday, but I had to get these on here, since I soon will(or already have) posted these on Lego Ideas. If you just came here from Lego Ideas, thanks for your support, and please consider following me on Ideas or me in Blogger to see even more cool MOCs. Lets dive it. To start off, here is a shot of all the Jaegers. For those of you who don't know what a Jaeger is, it is a 2 person piloted mech from The movie Pacific Rim and Pacific Rim Uprising.  Lets start off with my first one, Midnight Redeemer. And yes, I did name them all. If you have suggestions for better names, please comment them down below!  As you can see, he has two twin swords, which can easily detach from the clips on the wrists. Here on the back, you can faintly see the jump pack installed. I usually do jump packs in place of jet packs, because I feel that would make the Jaegers too OP. One final ability is t
Post a Comment
Read more

Excalibur, the mini mech part 1.

Hello again! Welcome to another exiting post from Legomaster! In this post I will be showing you how to build an amazing MOC( my own creation ) , Excalibur, the medieval mini mech! This is a part one of a two part post. The first post (this one) will show you how to build the top torso. Here is the mech itself, Excalibur! Here are the pieces to start off with. Start by taking one 1x2 double stud brick and attach a 1x2 bar plate piece on each side as shown. On top of each 1x2 bar plate, attach a 1x1 circular clip plate as shown. On the back of the 1x1 circular clip bar attach a inverted 1x2 slope to the back as shown.  On the front of the 1x1 circular clip plate and part of the front of the inverted 1x2 slope, attach a 1x2 brick with side studs. That is the brick you started with in the beginning. On the inner bottom sides of both of the 1x2 brick with side studs, attach a 1x1 plate side clip as shown. Do the same thing on the outer bot
Post a Comment
Read more